Weld-On IPS 1829, 4 oz.

Weld-On IPS 1829 4OZ.SUBSTRATE RECOMMENDATIONSA wide variety of plastics and non-plastics to themselves and to each other; such as flexible and rigid vinyls, acrylics, urethane foam and others to wood, metal, glass, masonry, canvas, rubber and other non-plastics.BONDING RECOMMENDATIONSWELD-ON 1829 is a medium bodied, water-resistant, modified elastomer and light tan in color. It is a part solvent cement which cures with the dissipation of solvent to a very tough flexible film. It forms strong joints with rigid materials, but affords high impact resistance because of its flexibility. It is highly resistant to water, oil and gasoline. A thin film exposed to air will dry in 3 to 7 minutes.USESWELD-ON 1829 is being used in marine applications for bonding plasticized vinyls to masonry and metal and patching vinyl sheets. It is also used in upholstering vinyl seats, bonding vinyl to urethane foam, canvas, as well as other materials and attaching plastic letters to many substrates. OTHER USES: Bonding aluminum or vinyl extrusions to concrete, repair of sporting equipment, leather goods, shoes, saddles, belts and handbags.ADHESIVE PROPERTIES AND CHARACTERISTICSCOLOR: Tan VISCOSITY: 1500 cps SPECIFIC GRAVITY:86 .040 COVERAGE: 10mil: 26 sq. ft/Pint 210 sq. ft/Gallon 20mil: 13 sq. ft/Pint 105 sq. ft/GallonDIRECTION FOR USEClean surfaces to be joinedCoat each mating surface (2 coats if porous). Allow about 2 to 5 minutes for each to dry before assembly.Film should be slightly tacky but not enough to transfer to the fingers using a light touch. Heavy coating may require slightly longer to dry.Press parts firmly together. Use clamps or weights until cement has set sufficiently for handling strength. If parts are strained, do not remove clamps for at least a few hours, depending on materials and room temperature.Initial bond is suitable for handling. For good strength, allow 16 to 24 hours and bond strength will continue to increase for a number of weeks.When applying cement to one piece, bring other piece in contact immediately and maintain contact for a few hours before removing clamps or weights.SHELF LIFETwo years expectancy in tightly sealed containers. Stability of the product is limited by the permanence of the container and the evaporation of the solvent when the container is open. Evaporation of solvent will cause the cement to thicken and reduce the effectiveness of the cement.SHIPPINGShipping Information for Gallon and Above: DOT Shipping Name: Adhesive. DOT Hazard Class: 3. ID # UN1133. Packaging Group: II. Label: Flammable Liquid.Shipping Information for Less than One Gallon: DOT Shipping Name: Consumer Commodity. DOT Shipping Class: ORM-D.Shipping Information for Individual Container Larger than One Liter: DOT Shipping Name: Adhesive. DOT Hazard Class: 3. ID #: UN1133. Packaging Group: II. Label: Flammable Liquid.Shipping Information for Less than One Liter: DOT Shipping Name: Consumer Commodity. DOT Shipping Class: ORM-D.SAFETY AND ENVIRONMENTAL PRECAUTIONSThis product is a flammable, fast evaporating, solvent cement. It is considered a hazardous material. In conformance with the Federal Hazardous Substances Labeling Act, the following hazards and precautions are given. Purchasers who may re-package this product must also conform to all local, state and federal labeling, safety and other regulations.CAUTION! FLAMMABLE VAPOR HARMFUL MAY BE HARMFUL IF SWALLOWED MAY IRRITATE SKIN OR EYES Keep out of reach of children. Do not take internally. Keep away from heat, spark, open flame and other sources of ignition. Keep container closed when not in use. Store in the shade between 40F and 110F. Use only with adequate ventilation. Avoid breathing of vapors. Atmospheric levels should be maintained below established exposure limit values contained in Section II and VIII of the Material Safety Data Sheet. If airborne concentrations exceed those limits, use of a NIOSH-approved organic vapor cartridge r